Hi. I am starting testing with a new way of laying down the magline. I am having trouble getting the 'Keld metode ' consistent and good enough.
Going to route a 4mm track then 3d print a 4 X 4mm infill with the magwire within.
Altenate printing with magnetic pla and see if I can get the right tracktion.
Also thinking of printing lanechangesections with mag.pla.
I will be back with progress if any....
Routing a Magracing track.
Routing a Magracing track.
- Attachments
-
- 0_DSC_3407.JPG (67.87 KiB) Viewed 19597 times
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
Routing the OSB board is a nightmare. Due to the uneven structure it is impossible to get some nice straight routing.
So instead of struggling i used a 6 mm bit and let it slip-slide, thinking it would leave a useful track of 4 mm in the middle.
It seems to work I just have to cut the worst places with an x-acto knife.
The uneven track will hold the pla-track n place.
Some pic.
So instead of struggling i used a 6 mm bit and let it slip-slide, thinking it would leave a useful track of 4 mm in the middle.
It seems to work I just have to cut the worst places with an x-acto knife.
The uneven track will hold the pla-track n place.
Some pic.
- Attachments
-
- 0_DSC_3409.JPG (78.17 KiB) Viewed 19586 times
-
- 0_DSC_3410.JPG (87.74 KiB) Viewed 19586 times
-
- 0_DSC_3411.JPG (77.72 KiB) Viewed 19586 times
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
I think you are making an easy job difficult Kim. Glue the wire down - plaster it level. Job done!
Re: Routing a Magracing track.
You are probably right Wes, but not everyone has a black belt in plastering.
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
That OSB board aint worth to use, throw it out an buy a mdf. And stop waiting time with that printing.
When i can get a good driwing 1/24 i will use my lasercutter to make the slot to the wires, it is easy to do and very precise.
When i can get a good driwing 1/24 i will use my lasercutter to make the slot to the wires, it is easy to do and very precise.
/Keld
Re: Routing a Magracing track.
Sure Keld, MDF is way better, I just had these leftover by hand.
And these sections I make are reusable, I can just pop them out and use them om a new track.
BTW when you use laser, can you cut a slot only or will you cut all through?
And these sections I make are reusable, I can just pop them out and use them om a new track.
BTW when you use laser, can you cut a slot only or will you cut all through?
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
My 40cm sections with wire.
- Attachments
-
- 0_DSC_3414.JPG (77.36 KiB) Viewed 19515 times
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
I can engrave, and adjust the laser power to go as deep as i want to
See some of my stuff here on the front page: https://butik.slotworld.dk
See some of my stuff here on the front page: https://butik.slotworld.dk
/Keld
Re: Routing a Magracing track.
Track layout is down. Now spotguing and some infill at the worst spots along the track.
- Attachments
-
- 0_DSC_3415.JPG (72.24 KiB) Viewed 19502 times
Racing Regards
Kim K.
Kim K.
Re: Routing a Magracing track.
No way you can drop plastering on OSB boards. ![☺️](https://cdn.jsdelivr.net/gh/s9e/emoji-assets-twemoji@11.2/dist/svgz/263a.svgz)
- Attachments
-
- 0_DSC_3416.JPG (65.45 KiB) Viewed 19452 times
Racing Regards
Kim K.
Kim K.